Aircraft Systems and Flight: Anti-Ice and Deice system

 When flying in freezing temperatures, ice build-up is fairly common. Smaller aircraft are limited to the type of weather they are allowed to fly in so the larger planes are typically equipped with more preventative methods. The anti-ice and deice systems are used to prevent ice from forming on surfaces such as the leading edge of the wing and tail, pitot and static port openings fuel tank vents, stall warning devices, windshields, and propeller blades (Federal Aviation Administration (FAA). (2016). 

The common preventative methods include: 

  • Inflatable Deicing Boots
  • Thermal Anti-Ice System
  • Weeping Wing
  • Wind Screen Anti-Ice system
  • Electric Heating Method 
  • Alcohol or Electrically Heated Elements
Inflatable Deicing Boots
The Inflatable Deicing Boots are designed to protect the leading edge of the wing by the inflation of the rubber boots by the pneumatic pump. while the boot is inflating, the ice will crack and fall off the wing. Another method for the wing is the Thermal Anti-Ice System, this is one of the most effective methods with the use of heat. The hot air is directed from the engine's compressor section to the leading edge surface (Federal Aviation Administration (FAA). (2016). As the leading edge surface heats up, the ice is not able to form. An alternate method for the leading edge is the weeping wing, one of the less common among the three. The weeping wing is an antifreeze solution that is pumped out of the small holes onto the leading edge chemically breaking down the bond between the ice and the wing surface. The complexity of the inflatable boots poses alot of potential areas to fail. The surface deice annunciator is connected to pressure switches that indicate if the system has reached operating pressure. The loss of pressure appears through holes in the boots as the rubber deteriorates. However, in the situation that the boot fails to deflate,  there is a possibility of ice building on top of the boot making it impossible to remove the ice. In this case, the solution would be to pull the surface-deice circuit breaker removing the current from flow valves and back to their normal position allowing the ability to use the system manually.

Another common area that is also prone to ice buildup is the windscreen. There are two methods, the windscreen anti-ice system and the electric heating method. The anti-ice system of the windscreen uses alcohol to flow onto the windscreen to prevent ice buildup. This method is only used before the ice begins to collect (Federal Aviation Administration (FAA). (2016). As for the electric heating method, conductive materials in the windshield cause heat to flow across the screen to prevent ice from building. This method is only used in flight. If the windshield protection fails in icing conditions it will be difficult to land with low visibility if the surface is also at freezing temperatures (Estaff. (2014). It is possible for the defroster to provide some forward visibility, enough to view land and somewhat of the runway. However, If the aircraft has more than one defrost vent, blocking the vents with a coat or rag will pump more heated airflow out of the pilot's vents.

The last major surface is the propellers which use the method of alcohol or electrically heated elements to remove ice. The use of a discharge nozzle is pointed towards the root of the blade discharging the alcohol and is driven down the leading edge of the blade preventing the ice from forming of the leading edge of the propeller. If a boot fails to heat one of the blades, the result of an unequal blade loading can occur causing severe propeller vibrations (Federal Aviation Administration (FAA). (2016). The vibrations should be stopped as soon as possible to avoid engine or mount damage. A failure of the heating element or wiring will result in the propeller ammeter showing low or zero amps at one point in the sequence. This can be temporarily improved by varying the propeller RPM to cause the blades to move and hopefully the ice will eventually fall off (Estaff. (2014). Some heat methods have a manual that bypasses the timer and causes each element to be heated simultaneously.


It is important to ensure during the precheck that all anti-ice and deice systems are correctly working. Some failures in deice methods are non-reversable during flight and do not have a solution. Areas such as the inflatable boot are not able to be patched during flight presenting the possibility of not being able to remove the ice on major airfoil surfaces until reaching warmer temperatures.


References

Estaff. (2014). Ice Equipment Failures.
        https://www.ifr-magazine.com/training-sims/ice-equipment-failures/

Federal Aviation Administration (FAA). (2016). Pilot’s Handbook of Aeronautical Knowledge (PHAK). Retrieved https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/phak/


Comments

Popular Posts